1.
- connecting a PC to a router’s console port
- connecting two routers together via their fast ethernet ports
- connecting two switches together at gigabit speeds
- connecting a PC to a switch at Gigabit Ethernet speeds
- connecting two devices with the same interface type at Fast Ethernet speeds
03. What makes fiber preferable to copper cabling for interconnecting buildings? (Choose three.)
- greater distances per cable run
- lower installation cost
- limited susceptibility to EMI/RFI
- durable connections
- greater bandwidth potential
- easily terminated
- STP
- UTP
- coaxial
- single-mode fiber
- multimode fiber
- loss of signal strength as distance increases
- time for a signal to reach its destination
- leakage of signals from one cable pair to another
- strengthening of a signal by a networking device
- 30
- 256
- 2046
- 2048
- 4094
- 4096
- 255.255.0.0
- 255.255.255.0
- 255.255.254.0
- 255.255.248.0
- 255.255.255.0
- 255.255.255.192
- 255.255.255.224
- 255.255.255.240
- 255.255.255.248
- cross-over
- straight-through
- rollover
- patch cable
10. Which device is used to create or divide broadcast domains?
- hub
- switch
- bridge
- router
- repeater
Refer to the exhibit. What destination IP address will PC1 place in the header for a packet destined for PC2?
- 192.168.1.1
- 192.168.2.1
- 192.168.2.2
- 192.168.3.1
- 192.168.3.54
Refer to the exhibit. Based on the IP configuration shown, what would be the result of Host A and Host B attempting to communicate outside the network segment?
- both host A and B would be successful
- host A would be successful, host B would fail
- host B would be successful, host A would fail
- both Host A and B would fail
- RJ 11
- DB 60
- Winchester 15 pin
- DB 9
- smart serial
- RJ 45
Refer to the exhibit. How many subnets are required to support the network that is shown?
- 2
- 3
- 4
- 5
- cable color code association
- cable selection and configuration
- use of cable testers to determine pinouts
- the automatic detection and negotiating of MDI/MDIX operation of the port
- the enabling of the mechanism to electrically swap the transmit and receive pairs
Refer to the exhibit. A student is setting up a home network primarily used for extensive file transfers, streaming video, and gaming. Which network device is best suited to these types of activities in the topology shown?
- wireless access point
- router
- hub
- switch
- They propagate broadcasts.
- They enlarge collision domains.
- They segment broadcast domains.
- They interconnect different network technologies.
- Each router interface requires a separate network or subnet.
- They maintain a common frame format between LAN and WAN interfaces.
Refer to the exhibit. A network administrator has decided to use packet capture software to evaluate all traffic from the student subnet on the way to the Internet. To ensure that all packets are captured, what network device should be used to connect the monitoring station to the network between R1 and R2?
- hub
- router
- firewall appliance
- wireless access point
Refer to the exhibit. Assume that all devices are using default settings. How many subnets are required to address the topology that is shown?
- 1
- 3
- 4
- 5
- 7
Refer to the exhibit. Which three statements are true about the exhibited topology? (Choose three.)
- Hosts B and C are in the same subnet.
- Five broadcast domains are present.
- Host B is using a crossover cable to connect to the router.
- Four broadcast domains are present.
- Five networks are shown.
- Host B is using a rollover cable to connect to the router.
- crossover cable
- straight through cable
- rollover cable
- V.35 cable
22.
Refer to the exhibit. Which three statements identify the type of cabling that would be used in the segments that are shown? (Choose three.)
- Segment 1 uses backbone cabling.
- Segment 1 uses a patch cable.
- Segment 3 uses patch cabling.
- Segment 3 uses vertical cabling.
- Segment 3 uses horizontal cabling.
- Segment 4 uses vertical cabling.
Refer to the exhibit. A network technician has been allocated the 192.168.1.0/24 private IP address range for use in the network that shown in the exhibit. Which subnet mask would be used to meet the host requirements for segment A of this internetwork?
- 255.255.255.128
- 255.255.255.192
- 255.255.255.224
- 255.255.255.240
- 255.255.255.248
4 comments:
Thanks for this information; I hope it will use much reader who looking you regularly likes me…
Regards,
ccna training institute in Chennai
Thanks for sharing. Keep sharing your knowledge on networking
Thank you for the practice test questions
CCNA course in Abu Dhabi
Thanks for great Information.
My experience about the CCNA course, I started training in CCNA, I was cheated by one fake course institute in Bangalore, then my friend suggest I join the Cloudsynergy CCNA course in Bangalore.
They are doing the best service in training, Now I learned the CCNA course at an affordable price. Thank you cloud synergy
CCNA course in Bangalore
Aws training in Bangalore
Post a Comment